Polymer Powder Coating Line

• Customization: Available
• After-sales Service: One Year
• Warranty: One Year
• Type: Single Side Spraying
• Compressed Air: 0.5-0.7MPa
• Open Wind Speed: 0.5m/Sec
• Transport Package: Case
• Specification: L2200xW2200xH2200(mm)
• Trademark: jinrong
• Origin: China
• Package Size: 220.00cm * 220.00cm * 220.00cm
• Package Gross Weight: 500.000kg

Product Description

Polymer powder coating line
Small spray room oven plan book
1. Design parameters (confirmed by the demander) :

serial number	name	Set up a plan based on data
1	product name
2	coating	powder

1. Equipment design: 

(1) Powder spraying system: a total of 1 sets;
1. Powder room description:
(1) The outer dimension of the powder spraying room: 2.2×2.2×2.2 meters (length × width × height)
(2) One side of the spray room is provided with a manual powder spraying port
(3) The chamber body wall and top plate are made of cold tie plate; The surface of the chamber is smooth and clean, and the imported "Sika" silicon-free sealant is poured into the joint between the plates, and there is no powder leakage. Powder cleaning is easy to operate.
2. Effective indicators of powder spraying room:

serial number	item	specification
	boundary dimension	L2200×W2200×H2200(mm)
	Operating port size	2200mm wide x 1500mm high
	Recovery treatment mode	Cartridge recovery
	type	Single side spraying
	compressed air	0.5-0.7MPa
	Open wind speed	0.5m/sec
	exhaust air rate	14000 m3/h
	Spray form	Manual duster gun (right or wrong two-station arrangement)
	Installed power of equipment	5.5KW

3. Materials used in the dusting room

serial number	name	specification
1	Chamber side wall panel and top panel	Galvanized sheet δ=1.2mm
2	soleplate	Galvanized sheet δ=1.2mm
3	Incoming and outgoing ports	Galvanized sheet δ=1.2mm
4	Floor support	Hot rolled steel plate δ=2.5mm
5	Recovery fan	There is one 5.5KW centrifugal fan
6	filter element	There are 6 quick-break 3290
7	blast pipe	0.7MM galvanized sheet
8	illumination	40W fluorescent lamp

                        
(2) Curing drying equipment (1 set)
Oven: enclosed
External size: L3.0m×W2.0m×H2.00m. See the section diagram of the scheme for details.
The baking path adopts "sandwich" insulation board assembly structure. The air supply pipe in the box is made of δ1.0 galvanized steel plate, the outer plate of the insulation board is made of δ0.60 color steel plate, the inner plate is made of δ0.60 galvanized steel plate, and the double side pressure reinforcement; The thickness of the insulation layer is 120mm. Hot air circulation is used to heat the drying passage. Its advantage is that the temperature in the drying passage is uniform, and the temperature difference between the upper, middle and lower three points along the cross section of the track is less than ±8 ° C, thus ensuring the consistency of the coating color of the workpiece.:

serial number	item	technical specification
1	Overall structure of drying chamber	box-type
2	Number of cars	two
3	External chamber size of drying chamber	L×W×H = 3.0×2.0×2.0 m
4	The insulation layer is thick	120mm
5	Thermal insulation material	High quality rock wool board
6	Thermal insulation material volume weight	120Kg/m3
7	Heat insulation board inside the plate material	δ0.60mm galvanized steel bar
8	Drying track insulation board external plate material	δ0.60mm Color steel reinforcement
9	Air supply duct and outlet	δ1.0mm galvanized plate
11	The average temperature of the drying outdoor table	Not higher than the ambient temperature 10ºC
12	Oven heating	The temperature rises to 180 ° C ≤40 minutes
13	Heating chamber power	27KW,1set
14	Drying room bridge column and frame	δ2.5 The hot rolled plate is flanged into various shapes and 75×50 special Angle steel as the base plate
15	Drying room upper and lower wrapping Angle	δ2.5mm carbon steel to make the upper wrapping Angle, δ2.5mm carbon steel to make the lower wrapping Angle, spray paint treatment

(3) Electrical control system
Electrical control adopts decentralized setting centralized control mode.
The design, selection, manufacture and installation of electrical equipment shall comply with the relevant national standards.
The electrical control cabinet has neat surface, beautiful appearance and reasonable panel layout for easy observation and operation.
Selected the new series of devices promoted by the state, reliable performance, advanced technology.
Cabinet door handles are equipped with locks.
The cabinet door wires are arranged neatly and beautifully, the wiring and direction are standardized, and bundled into bundles to achieve horizontal and vertical. If the wire wants to turn a right Angle, bend the corner into a small circular arc.
The wire has good and firm contact with the electrical terminals. The insulation resistance between wires is greater than 1 megohm.
The wire should be marked with a clear line number at the wiring terminals of each electrical appliance, and it is not easy to wear and fade.
Each connector is marked firmly.
The marking symbol and the route number of each component in the cabinet correspond accurately to the electrical control diagram for easy inspection and maintenance.
All components are manufactured by national designated manufacturers or imported products.
Electrical equipment should have good grounding, grounding resistance in line with national standards.
The main vital parts are made of Delixi products, and the temperature controller is made of intelligent products.
4. Energy consumption table:

serial number	item		Amount used
1	installed power	Recovery fan	5.5KW
		oven	27KW
		installed power	32.5KW
2	Compressed air consumption (m3/min)	0.20	0.2
3	Compressed air requirement	Note: Gas supply standard: oil ≤0.1ppm water ≤1.3g/m3 Compressed air supply: 6.0 ~ 10.0m3 / min
4	power requirement	Three-phase five-wire system, voltage 380V, 220V voltage fluctuation ≤5%

                           
5. Acceptance and after-sales service
(1) equipment installation completion time: 30 days;
Equipment design time: 2 days;
Production time: 25 days;
Equipment installation time: 2 days;
Expected commissioning time: 1 day;
The warranty period of the equipment is one year, and the supplier is responsible for the implementation of "three guarantees" for the quality problems of the equipment during the warranty period. The supplier guarantees that the design, material selection, processing, manufacturing, inspection and acceptance provided must conform to the relevant national or industrial standards, and are brand-new products without use, and the specifications and specifications are completely consistent with those described in the tender documents, so as to ensure the normal operation of the equipment under the condition of correct installation, normal operation and maintenance.
The supplier shall be responsible for the "three guarantees" during the specified quality guarantee period, and shall be responsible for the failure caused by the defects of design, manufacturing, process or materials, and shall repair and replace the defective parts or the whole machine free of charge. We have a wealth of experience in engineering contracting, fully able to complete the entire project on time and quality, to ensure product quality, users do not have to bear any risk.
5, we will send experienced personnel to the site responsible for construction and installation and commissioning.
6. The Supplier shall be responsible for training the operator and maintenance personnel of the Demander, ensuring that the Demander shall be trained a number of personnel who can skillfully operate all equipment and maintain the equipment. The specific number shall be determined by Party A.
7. Party A and Party B shall establish a long-term (more than 5 years) stable supply relationship of spare parts, and Party B shall provide various spare parts to Party A on a preferential basis.
8. After the Contract takes effect, Party B shall provide Party A with the following technical documents (in the number required by Party A) before commissioning: Equipment Qualification Certificate; Equipment operation manual; Equipment basic drawing, layout drawing, electrical schematic diagram.
9. The final acceptance of the equipment shall be carried out at the site of the user unit according to the requirements of the contract and technical agreement.